Diorganotin dications stabilized by neutral ligands in the solid state: [R2Sn(H2O)2(OPPh3)2](O3SCF3)2 (R = Me, Bu)

The synthesis of [R₂Sn(H₂O)₂(OPPh₃)₂](O₃SCF₃)₂ (R = Me (1), Bu (2)) by the consecutive reaction of R₂SnO (R = Me, Bu) with triflic acid and Ph₃PO is described. Compounds 1 and 2 feature dialkyltin(IV) dications [R₂Sn(H₂O)₂(OPPh₃)₂]^₂+ apparently stabilized by the neutral ligands in the solid state. Compounds 1 and 2 readily dehydrate upon heating at 105 and 86 °C, respectively. The preparative dehydration of 1 afforded [Me₂Sn(OPPh₃)₂(O₃SCF₃)](O₃SCF₃) (1a), which features both bidentate and non-coordinating triflate anions. In compounds 1 and 2 the ligands Ph₃PO and H₂O are kinetically labile in solution and undergo reversible ligand exchange reactions. Compounds 1, 1a and 2 were characterized by multinuclear solution and solid-state NMR spectroscopy, IR spectroscopy, electrospray mass spectrometry, conductivity measurements, thermogravimetry and X-ray crystallography.

Characterization of hot-pressed films from superfine wool powder

In this study, superfine wool powder was plasticized with glycerol and hot-pressed into a film. Scanning electron microscopy photos showed that the superfine wool powder could be molded into a smooth film and that the wool powder was distributed evenly in the cross section of the film. Fourier transform infrared analysis revealed no substantial changes in the chemical structure of the wool powder after hot pressing, but the absorbing peaks of glycerol were found in the spectrum. X-ray diffraction analysis showed that the overall crystallinity increased after the wool powder was hot-pressed into film. Thermogravimetry (TG) analysis indicated that the thermal stability of the hot-pressed film decreased. A transition point appeared in the TG curve of the wool hot-pressed film as glycerol was added. The differential thermal analysis curve of the film showed sharp absorbing peaks similar to that of wool powder. With increasing glycerol content, the film showed increasing ductility and softness.

Microstructures and bond strengths of the calcium phosphate coatings formed on titanium from different simulated body fluids

Calcium phosphate (Ca-P) coatings were deposited on Ti substrates by a biomimetic method from m-SBF and 10× SBF, respectively. Comparative study of microstructures and bond strengths of the Ca-P coatings deposited from those different SBFs was carried out. Effect of the surface roughness of the substrates on the bond strength of the Ca-P coatings was also studied. Scanning electron microscopy (SEM), X-ray diffractometry (XRD), Fourier transformed infrared spectroscopy (FTIR), inductive coupled plasma spectrometry (ICP) and thermogravimetry (TG) were used to characterize the Ca-P coatings. The bond strengths between the coatings and Ti substrates were measured using an adhesive strength test. Results indicated that the ionic concentrations of the SBFs and the surface roughness of the substrate had a significant influence on the formation, morphology and bond strength of the Ca-P precipitates. The induction period of time to deposit a complete Ca-P layer from the m-SBF is much longer, but the Ca-P coating is denser and has higher bond strength than that formed from the 10× SBF. The Ti with a surface roughness of R_a 0.64 µm and R_z 2.81 µm favoures the formation of a compact Ca-P coating from the m-SBF with the highest bond strength of approximately 15.5 MPa.

Study on thermooxidative degradation of poly(vinyl alcohol)/silica nanocomposite prepared with SAM technique

The thermooxidative degradation of poly (vinyl alcohol)/silica (PVA/SiO2) nanocomposite prepared with self-assembly monolayer (SAM) technique is investigated by using a thermogravimetry (TG) and Fourier transform infrared spectroscopy coupled thermogravimetry (FTIR/TG). The results show that although the thermooxidative degradation process of prepared nanocomposite is similar to that of the pure PVA, its thermooxidative stability has been greatly improved.

Visible transparent, UV-blocking polymer nanocomposite films containing nano-sized organic-LDH (Layered Double Hydroxide) hybrid

A nano-sized Mg2Al layered double hydroxide (LDH) was used for encapsulating an organic UV absorber, 2-hydroxy-4- methoxybenzeophenone-5-sulfonic acid (HMBS), to produce HMBS@LDH hybrid nano-platelets. Upon dispersing this organic-inorganic hybrid LDH into ethylene-vinyl alcohol copolymer (EVOH) for film casting, a thin polymer
nanocomposite film that is UV opaque but highly transparent to visible light (higher than 90%) was formed. Thermogravimetry (TG) analysis confirmed that the intercalation of HMBS into LDH considerably increased the thermal stability of HMBS. Such an improvement was attributed to the strong guest-host interaction between the HMBS anions and the LDH layers. Also, the nanocomposite films were flexible and had good mechanical properties.

Superhydrophobic nanofibre membranes : effects of particulate coating on hydrophobicity and surface properties

Superhydrophobic electrospun polyacrylonitrile nanofibre membranes have been prepared by surface coating of silica nanoparticles and fluorinated alkyl silane. The coated membranes were characterised by scanning electron microscopy, water contact angle, thermogravimetry analysis, Brunauer–Emmett–Teller, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy. It was shown that the loading of nanoparticle on the nanofibre membrane was controlled by the particle concentration in the coating solution, which played a critical role in the formation of superhydrophobic surface. Increased particle loading led to higher surface roughness and WCA. The nanoparticle coating had little influence on the porosity of the nanofibre membranes. However, overloading of the particles would affect the specific surface area of the nanofibre membrane.

Can macroalgae contribute to blue carbon? An Australian perspective

Macroalgal communities in Australia and around the world store vast quantities of carbon in their living biomass, but their prevalence of growing on hard substrata means that they have limited capacity to act as long-term carbon sinks. Unlike other coastal blue carbon habitats such as seagrasses, saltmarshes and mangroves, they do not develop their own organic-rich sediments, but may instead act as a rich carbon source and make significant contributions in the form of detritus to sedimentary habitats by acting as a “carbon donor” to “receiver sites” where organic material accumulates. The potential for storage of this donated carbon however, is dependent on the decay rate during transport and the burial efficiency at receiver sites. To better understand the potential contribution of macroalgal communities to coastal blue carbon budgets, a comprehensive literature search was conducted using key words, including carbon sequestration, macroalgal distribution, abundance and productivity to provide an estimation of the total amount of carbon stored in temperate Australian macroalgae. Our most conservative calculations estimate 109.9 Tg C is stored in living macroalgal biomass of temperate Australia, using a coastal area covering 249,697 km2. Estimates derived for tropical and subtropical regions contributed an additional 23.2 Tg C. By extending the search to include global studies we provide a broader context and rationale for the study, contributing to the global aspects of the review. In addition, we discuss the potential role of calcium carbonate-containing macroalgae, consider the dynamic nature of macroalgal populations in the context of climate change, and identify the knowledge gaps that once addressed will enable robust quantification of macroalgae in marine biogeochemical cycling of carbon. We conclude that macroalgal communities have the potential to make ecologically meaningful contributions toward global blue carbon sequestration, as donors, but given that the fate of detached macroalgal biomass remains unclear, further research is needed to quantify this contribution.

A novel water-soluble hydrophobically associating polyacrylamide based on oleic imidazoline and sulfonate for enhanced oil recovery

3-(2-(2-Heptadec-8-enyl-4,5-dihydro-imidazol-1-yl)ethylcarbamoyl)acrylic acid (NIMA), 3-(diallyl-amino)-2-hydroxypropyl sulfonate (NDS), acrylamide (AM) and acrylic acid (AA) were successfully utilized to prepare novel acrylamide-based copolymers (named AM/AA/NIMA and AM/AA/NDS/NIMA) which were functionalized by a combination of imidazoline derivative and/or sulfonate via redox free-radical polymerization. The two copolymers were characterized by infrared (IR) spectroscopy, 1H nuclear magnetic resonance (1H NMR), viscosimetry, pyrene fluorescence probe, thermogravimetry (TG) and differential thermogravimetry (DTG). As expected, the polymers exhibited excellent thickening property, shear stability (viscosity retention rate 5.02% and 7.65% at 1000 s-1) and salt-tolerance (10:000 mg L-1 NaCl: viscosity retention rate up to 17.1% and 10.2%) in comparison with similar concentration partially hydrolyzed polyacrylamide (HPAM). The temperature resistance of the AM/AA/NDS/NIMA solution was also remarkably improved and the viscosity retention rate reached 54.8% under 110 °C. According to the core flooding tests, oil recovery could be enhanced by up to 15.46% by 2000 mg L-1 of the AM/AA/NDS/NIMA brine solution at 80 °C.

Thermally stable imidazoline-based sulfonate copolymers for enhanced oil recover

Novel imidazoline-based sulfonate copolymers (noted PAMDSCM and PAMPSCM) were successfully prepared by copolymerization of acrylamide (AM), acrylic acid (AA), 1-acrylamido ethyl-2-oleic imidazoline (ACEIM) with the sodium salts of 3-(diallyl-amino)-2-hydroxypropyl (NDS) or 2-acrylamido-2-methylpropane sulfonic acid (AMPS), respectively. The copolymers were characterized by infrared (IR) spectroscopy, 1H nuclear magnetic resonance (1H NMR) spectroscopy, pyrene fluorescence probe spectroscopy, viscosimetry and thermogravimetry (TG). Both PAMDSCM and PAMPSCM copolymers had excellent high-temperature tolerance in comparison with the same concentration of HPAM, and the residual viscosities were 32.0 mPa s and 31.3 mPa s (viscosity retention rates were 38.8% and 37.1%) at 140 °C, respectively. The copolymers possessed superior long-term thermal stability and their residual viscosity rates were up to 81.8% and 63.8% (52.9 mPa s and 47.1 mPa s) lasting 1.5 hours at 100 °C and 170 s-1, respectively.

Comparison of marine macrophytes for their contributions to blue carbon sequestration

Many marine ecosystems have the capacity for long-term storage of organic carbon (C) in what are termed "blue carbon" systems. While blue carbon systems (saltmarsh, mangrove, and seagrass) are efficient at long-term sequestration of organic carbon (C), much of their sequestered C may originate from other (allochthonous) habitats. Macroalgae, due to their high rates of production, fragmentation, and ability to be transported, would also appear to be able to make a significant contribution as C donors to blue C habitats. In order to assess the stability of macroalgal tissues and their likely contribution to long-term pools of C, we applied thermogravimetric analysis (TGA) to 14 taxa of marine macroalgae and coastal vascular plants. We assessed the structural complexity of multiple lineages of plant and tissue types with differing cell wall structures and found that decomposition dynamics varied significantly according to differences in cell wall structure and composition among taxonomic groups and tissue function (photosynthetic vs. attachment). Vascular plant tissues generally exhibited greater stability with a greater proportion of mass loss at temperatures > 300 degrees C (peak mass loss -320 degrees C) than macroalgae (peak mass loss between 175-300 degrees C), consistent with the lignocellulose matrix of vascular plants. Greater variation in thermogravimetric signatures within and among macroalgal taxa, relative to vascular plants, was also consistent with the diversity of cell wall structure and composition among groups. Significant degradation above 600 degrees C for some macroalgae, as well as some belowground seagrass tissues, is likely due to the presence of taxon-specific compounds. The results of this study highlight the importance of the lignocellulose matrix to the stability of vascular plant sources and the potentially significant role of refractory, taxon-specific compounds (carbonates, long-chain lipids, alginates, xylans, and sulfated polysaccharides) from macroalgae and seagrasses for their long-term sedimentary C storage. This study shows that marine macroalgae do contain refractory compounds and thus may be more valuable to long-term carbon sequestration than we previously have considered.

Kinetic model for thermal dehydrochlorination of chlorinated natural rubber with different chlorine content

A novel model for calculating dehydrochlorination kinetics at a lower temperature of chlorinated natural rubber (CNR) is presented. It has been observed that dehydrochlorination is complex and involves three different stages. A model that accounts for dehydrochlorination at lower temperature is proposed. The kinetic parameters are obtained from dehydrochlorination experiments at 60-90 °C. The results of the kinetic calculation show that the apparent activation energy decreases with an increment of chlorine content. Higher chlorine content CNR makes it easier to remove hydrochloric acid when heated, but its dehydrochlorination rate affected by temperature is significantly less than that of the sample with a lower chlorine content. The thermogravimetric/derivative thermogravimetry results show that the beginning temperature of thermo-oxidative degradation rises with the increment of chlorine content. During the heating process, the higher chlorine content CNR is more stable than the lower one. The results suggest the storage conditions and basis for selection of appropriate temperature for the preparation of CNR from latex.

A novel α-aminophosphonic acid-modified acrylamide-based hydrophobic associating copolymer with superb water solubility for enhanced oil recovery

As a non-renewable resource, the rational exploitation of oil has attracted a large amount of attention. Among many methods for enhanced oil recovery, polymer flooding is the most suitable method of chemical flooding for non-marine reservoirs and therefore various modified acrylamide-based copolymers have been studied. In this study, a novel α-aminophosphonic acid-modified hydrophobic associating copolymer was successfully synthesized by copolymerization of acrylamide, acrylic acid, N-allyldodecanamide and 1-(dimethylamino)allylphosphonic acid. The copolymer was characterized by FT-IR, 1H NMR and thermogravimetry and exhibited superior water solubility and thickening capability. Subsequently, the shear resistance, temperature resistance and salt tolerance of the copolymer solution were investigated. The value of apparent viscosity retention of a 2000 mg L-1 copolymer solution was as high as 58.55 mPa s at a shear rate of 170 s-1 and remained at 40.20 mPa s at 120 °C. The values of apparent viscosity retention of 55.41 mPa s, 59.95 mPa s and 52.97 mPa s were observed in solutions of 10000 mg L-1 NaCl, 1200 mg L-1 MgCl2, and 1200 mg L-1 CaCl2, respectively. These were better than those of partially hydrolyzed polyacrylamide under the same conditions. In addition, an increase of up to 14.52% in the oil recovery rate compared with that for water flooding could be achieved in a core flooding test using a 2000 mg L-1 copolymer solution at 65 °C.